EN 13274-4:2020
(Main)Respiratory protective devices - Methods of test - Part 4: Flame test
Respiratory protective devices - Methods of test - Part 4: Flame test
This document specifies methods for flame tests to be applied to respiratory protective devices.
Atemschutzgeräte - Prüfverfahren - Teil 4: Flammenprüfungen
Dieses Dokument legt die Verfahren für Flammprüfungen zur Anwendung an Atemschutzgeräten fest.
Appareils de protection respiratoire - Méthodes d'essai - Partie 4 : Essais à la flamme
Le présent document spécifie les méthodes pour les essais à la flamme à appliquer aux appareils de protection respiratoire.
Oprema za varovanje dihal - Metode preskušanja - 4. del: Preskus s plamenom
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13274-4:2020
01-december-2020
Nadomešča:
SIST EN 13274-4:2001
Oprema za varovanje dihal - Metode preskušanja - 4. del: Preskus s plamenom
Respiratory protective devices - Methods of test - Part 4: Flame test
Atemschutzgeräte - Prüfverfahren - Teil 4: Flammenprüfungen
Appareils de protection respiratoire - Méthodes d'essai - Partie 4: Essais à la flamme
Ta slovenski standard je istoveten z: EN 13274-4:2020
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
13.340.30 Varovalne dihalne naprave Respiratory protective
devices
SIST EN 13274-4:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13274-4:2020
---------------------- Page: 2 ----------------------
SIST EN 13274-4:2020
EN 13274-4
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2020
EUROPÄISCHE NORM
ICS 13.220.40; 13.340.30 Supersedes EN 13274-4:2001
English Version
Respiratory protective devices - Methods of test - Part 4:
Flame test
Appareils de protection respiratoire - Méthodes d'essai Atemschutzgeräte - Prüfverfahren - Teil 4:
- Partie 4 : Essais à la flamme Flammenprüfungen
This European Standard was approved by CEN on 8 June 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13274-4:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13274-4:2020
EN 13274-4:2020 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Pre-requisites . 5
5 Nominal values and tolerances . 5
6 Six burner static test: Method 1 . 6
6.1 Principle . 6
6.2 Test rig . 6
6.3 Procedure. 7
7 Single burner static test: Method 2 . 9
7.1 Principle .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.